MODULAR
STEELWORK SOLUTIONS
Section Connectors

Pivot Joint GE F 80

Application

Applicable as a bracing element for single-arm cantilevers in conjunction with siFramo 80 section, and for the knee-brace reinforcing of siFramo 80 frame constructions. The pivot can be installed with angles from 25° to 155°.

Installation

Attachment of Joint GE F 80 to Beam Section TP F 80 by means of 4 Self Forming Screws FLS F at the base plate. The support profile TP F 80 plugged onto the octagon is also attached by means of 4 Self Forming Screws, so 8 Self Forming Screws are necessary in total. The cutting length of the support profile can be determined by the table below-mentioned. After installation at the desired angle the screws have to be tightened with 29.50 lbf/ft (40 Nm).

Technical Data

Type
Height H
[in]
Length L
[in]
Width B
[in]
Angle α
Maße der
Grundplatte
[mm]
GE F 80 - 80 140 80 80 25° - 155° -
GE F 80 - 80 q 140 80 80 25° - 155° 190 x 80 x 8

Type
Height H
[mm]
Length L
[mm]
Width B
[mm]
Angle α
GE F 80 - 80 140 80 80 25° - 155°


Cutting length c of support profile between two joints:


b [in]
3'-3 3/8"
b [in]
4'-11 1/16"
b [in]
6'-6 3/4"
b [in]
8'-2 7/16"
b [in]
9'-10 1/8"
α c [in] c [in] c [in] c [in] c [in]
25° 7'-13/16" 10'-11 1/2" 14'-10 1/8" 18'-8 13/16" 22'-7 1/4"
30° 5'-11 1/4" 9'-2 5/8" 12'-6" 15'-9 3/8" 19'-3/4"
35° 5'-1 5/8" 7'-11 7/8" 10'-10 1/8" 13'-8 9/16" 16'-6 13/16"
40° 4'-6 5/16" 7'-1 1/16" 9'-7 3/4" 12'-2 7/16" 14'-8 15/16"
45° 4'-1" 6'-4 15/16" 8'-8 3/4" 11'-11/16" 13'-4 7/16"
50° 3'-9 1/16" 5'-10 7/8" 8'-7/16" 10'-2 1/16" 12'-3 13/16"
55° 3'-5 3/4" 5'-5 15/16" 7'-5 15/16" 9'-6" 11'-6"
60° 3'-3 3/8" 5'-2 3/16" 7'-13/16" 8'-11 1/2" 10'-10 5/16"
65° 3'-1 3/8" 4'-11 1/16" 6'-8 7/8" 8'-6 9/16" 10'-4 3/16"


b [mm]
1000
b [mm]
1500
b [mm]
2000
b [mm]
2500
α a [mm] c [mm] c [mm] c [mm] c [mm]
25° 2095 2155 3340 4525 5710
30° 1701 1810 2810 3810 4810
35° 1410 1565 2435 3305 4180
40° 1184 1380 2160 2940 3720
45° 1000 1245 1955 2660 3370
50° 846 1145 1800 2450 3100
55° 713 1060 1670 2285 2895
60° 596 1000 1580 2155 2730
65° 489 950 1500 2055 2605

a =
vertical length from centerline of joint to bottom of profile at connection
b =
horizontal length of cantilever from connection to centerline of joint
c =
cutting length of support profile between two joints
α =
angle at the opposite of the vertical bracing

Material:
Steel, HCP

TypeW
[lb]
W
[kg]
Quantity
[pack]
Part
number
GE F 80 - 804.632.11 113835
GE F 80 - 80 q3.01 113834